掺钪AlN材料特性及HBAR器件性能研究

该文基于掺钪AlN薄膜制备了高次谐波体声波谐振器(HBAR),研究了钪(Sc)掺杂浓度对AlN压电薄膜材料特性及器件性能的影响。研究表明,当掺入Sc的摩尔分数从0增加到25%时,压电应力系数e₃₃增加、刚度 下降,导致Al₁-_xSc_xN压电薄膜的机电耦合系数 从5.6%提升至15.8%,从而使HBAR器件的有效机电耦合系数 提升了3倍。同时,当Sc掺杂摩尔分数达25%时,Al₁-_xSc_xN(x为Sc掺杂摩尔分数)压电薄膜的声速下降13%,声学损耗提高,导致HBAR器件的谐振频率和品质因数降低。     

ZnO·2.7Al2O3 nanocomposite with high optical transparency

Here we report a transparent dual-phase ZnO·2.7Al₂O₃ ceramic. The composite is pore-free and consists of thin nanosheets with a spinel phase and a hexagonal phase, while the two phases match closely in both lattice and refractive index. Such features result in excellent optical transmittance (maximum value >80% in the visible spectrum) at comparable phase volume. This work may provide a new thought for the rational structural design of optical nanocomposites.     

Comparison between fluctuation of floating potential gradient and velocity of blob structure on HL-2A tokamak

Several results based on the Langmuir probes' data on the HL-2A tokamak are presented. The blob structures' radial and poloidal drift velocities, estimated by the gradient of floating potential and by time delay evaluation, are compared in different line-averaged density and electron cyclotron resonance heating conditions. A positive correlation is observed in the comparison between blobs' radial velocity estimated by the two methods mentioned above, regardless of the situation differences mentioned above. Correlation is also observed in the comparison between the blobs' poloidal velocity estimated by the two methods in different situations, while a shift due to the different line-averaged density is observed. These results imply that the radial gradient of floating potential may have some value as a reference during data analysis in low-parameter discharge.     

Densification mechanism and microstructure characteristics of nano- and micro- crystalline alumina by high-pressure and low temperature sintering

Fully dense ceramics with retarded grain growth can be attained effectively at relatively low temperatures using a high-pressure sintering method. However, there is a paucity of in-depth research on the densification mechanism, grain growth process, grain boundary characterization, and residual stress. Using a strong, reliable die made from a carbon-fiber-reinforced carbon (C_f/C) composite for spark plasma sintering, two kinds of commercially pure α-Al₂O₃ powders, with average particle sizes of 220 nm and 3 μm, were sintered at relatively low temperatures and under high pressures of up to 200 MPa. The sintering densification temperature and the starting threshold temperature of grain growth (T_sg) were determined by the applied pressure and the surface energy relative to grain size, as they were both observed to increase with grain size and to decrease with applied pressure. Densification with limited grain coarsening occurred under an applied pressure of 200 MPa at 1050 °C for the 220 nm Al₂O₃ powder and 1400 °C for the 3 μm Al₂O₃ powder. The grain boundary energy, residual stress, and dislocation density of the ceramics sintered under high pressure and low temperature were higher than those of the samples sintered without additional pressure. Plastic deformation occurring at the contact area of the adjacent particles was proved to be the dominant mechanism for sintering under high pressure, and a mathematical model based on the plasticity mechanics and close packing of equal spheres was established. Based on the mathematical model, the predicted relative density of an Al₂O₃ compact can reach ～80 % via the plastic deformation mechanism, which fits well with experimental observations. The densification kinetics were investigated from the sintering parameters, i.e., the holding temperature, dwell time, and applied pressure. Diffusion, grain boundary sliding, and dislocation motion were assistant mechanisms in the final stage of sintering, as indicated by the stress exponent and the microstructural evolution. During the sintering of the 220 nm alumina at 1125 °C and 100 MPa, the deformation tends to increase defects and vacancies generation, both of which accelerate lattice diffusion and thus enhance grain growth.     

微纳层叠聚丙烯腈凝胶流动特性的数值模拟研究

建立了层叠流道的三维模型和有限元网格模型，根据流变测试数据，采用Polymat对物料的黏度模型参数进行拟合，并利用Polyflow软件对聚丙烯腈（PAN）凝胶在层叠流道内的三维等温流动过程进行了数值模拟分析。研究发现，当入口流量增大时，层叠流道出口速度的不均匀性增加；沿流动方向流道内压力逐渐降低，并在出口处降低至同一最低值；流道进出口压力差与入口流量大小具有正相关性；在流道的中心截面上剪切速率分布均匀，波动较小。     

循证之证与康复之途*—— CCRC社区中的康复花园循证设计探索

疫情下医养机构封闭化管理已经步入 常态化，老年居民的心理健康受到了抑郁、焦虑 等问题的挑战。康复花园作为养老社区中重要 的心理生理康复空间，需以循证设计为原则， 为新形势下的养老社区提供切实可行的康复空 间。本文以西南地区某持续照护型（CCRC）养 老社区项目实践为载体，梳理阐述循证设计在 康复花园中完整的运用实践路径，总结我国循 证设计流程模型，为风景园林的循证实践提供 全链条式的解析和验证。本文尝试提出基于系 统医学评估指标的证据收集创新体系，为康复 花园循证设计提供运用实例，对康复花园的康 复绩效提出基于证据的定量评估模式。     

基于代理模型的固体动力杀伤器气动外形优化研究

分析了固体动力杀伤器的气动外形设计参数。通过进化神经网络构建气动外形参数与气动特性之间的代理模型，然后确定了气动外形优化方法，并完成了算例验证。结果表明：通过代理模型开展固体动力杀伤器气动外形优化是可行的，能够大大缩短杀伤器气动外形优化周期。     

薄膜铂电阻元件稳定性测试与分析

高端军事应用环境对测温传感器提出了小结构、高精度、良好的长期稳定性等要求,采用溅射方式制备的薄膜铂电阻元件成为了首选。通过分析薄膜铂电阻元件的结构、工艺,探讨影响稳定性的主要因素,包括薄膜缺陷、杂质、电迁移、结构封装应用与温度应力等。选择薄膜铂电阻在水三相点下的电阻值作为稳定性的比较基准,设计了一款不大于3mK的高精度测试系统。通过对薄膜铂电阻元件进行高温电寿命试验和温度冲击试验,评估得出薄膜铂电阻元件长期稳定性达到10mK,满足设计需求。     

钢渣复合取代矿粉、砂和石用作混凝土掺合料与骨料及其性能分析

用风淬渣粉取代矿粉、电炉渣砂取代混合砂、电炉渣石取代碎石制备混凝土，分析了混凝土的内照射指数、外照射指数、f-CaO含量、沸煮膨胀值、比表面积、密度、含水率、容重、含泥量、泥块含量、坍落度、抗压强度及其化学组成、矿物组成与微观形貌，研究了钢渣的安全性与稳定性及风淬渣粉取代矿粉、电炉渣砂取代混合砂、电炉渣石取代碎石与钢渣复合取代矿粉、砂和石对混凝土性能的影响。结果表明，风淬渣粉、电炉渣砂和电炉渣石的安全性与稳定性满足国标要求，可用于混凝土。当风淬渣粉取代20wt%矿粉、电炉渣砂取代10wt%混合砂和电炉渣石取代20wt%碎石时，混凝土的性能最优。钢渣复合取代矿粉、砂和石的比例合适，可改善混凝土的界面结构密实度，尤其能提高混凝土养护后期的强度。     

基于弥散燃料颗粒开裂的金属基体裂纹特征模型

金属基弥散燃料元件在特殊工况下会发生表面起泡失效。燃料颗粒开裂是金属基体开裂的前提条件，只有当金属基体开裂后元件才会发生表面起泡。燃料颗粒开裂后，裂纹宽度和塑性区长度等裂纹特征决定了金属基体开裂行为。基于弹塑性断裂力学和应力平衡条件，建立了基于弥散燃料颗粒开裂的金属基体裂纹特征模型。计算结果表明：裂纹张开位移随退火温度和燃耗深度的升高而增加；裂纹尖端塑性区长度主要与退火温度相关。裂纹张开位移和塑性区长度的计算结果与实验数据均符合较好，验证了金属基体裂纹特征模型的有效性。